? 221 west industry court deer park, ny 11729 (631) 586 7600, fax 631 242 9798 ? ? world wide web - www.sensitron.com ? e-mail address - sales@sensitron.com ? sensitron ____ semiconductor technical data data sheet 202, rev - fixed negative 5.0 volt 1.5 amp regulator features: ? isolated hermetic package ? similar to industry type lm7905a maximum ratings all ratings are at t a = 25 c unless otherwise specified. parameter conditions typical limit units input voltage - - -35 vdc storage temperature range - - -65 to +150 c lead temperature soldering, 10 seconds - +300 c power dissipation (p d ) t c = +25 c t a = +25 c - - 15 3.0 w w maximum thermal resistance junction to case ( jc ) - - 4.2 c/w maximum thermal resistance junction to ambient ( ja ) - - 42 c/w maximum junction temperature (t j ) i o = 5.0 ma to 1.0 a - 150 c ambient operating temperature range (t a ) - - -55 to +125 c input voltage range recommended - - -6.5 to -25 vdc electrical characteristics parameter conditions typical limit units output voltage (v out ) t a = +25 c -5.00 -4.95 -5.05 v v line regulation (v rline ) -55 c t j +125 c v in = -25v to -7v - 20 mv load regulation (v rload ) -55 c t j +125 c i o = 5.0 ma to 1.5 a - 32 mv standby current drain (i scd ) - - 3.5 ma standby current drain change w/line ( ? i scd ) (line) v in = -25 v to -7.0 v - 0.8 ma standby current drain change w/load ( ? i scd ) (load) i o = 5.0 ma to 1000 ma - 0.5 ma dropout voltage (v do ) i o = 1.0a - 1.1 v peak output current (i o(pk) ) t a = +25 c - 3.3 a short circuit current (i os ) v in = -35v - 1.2 a ripple rejection ( ? v in / ? v out ) f o = 120 khz, v in = 10v i o = 5.0ma 56 - db output noise voltage (n o ) t a = +25 c 10 hz - 100khz - 40 v rms long term stability ( ? v out / ? t) t a = 25 c, t = 1,000 - 120 mv note : output voltage tolerance; +/- 1% @ 25 c, +/- 2% from -55 to +80 c SHD52624
? 221 west industry court deer park, ny 11729 (631) 586 7600, fax 631 242 9798 ? ? world wide web - www.sensitron.com ? e-mail address - sales@sensitron.com ? sensitron SHD52624 datasheet 202 revision - mechanical dimensions to-257 123 .200 .190 ( 5.08 4.82 ) .045 .035 ( 1.14 0.89 ) .120 ( 3.05 ) bs c .430 .410 ( 10.92 10.41 ) .420 .410 ( 10.67 10.41 ) .665 .645 ( 16.89 16.38 ) .537 .527 ( 13.64 13.39 ) 1.132 1.032 ( 28.75 26.21 ) .035 .025 ( 0.89 0.63 ) 3 pl aces .100 ( 2.54 ) bsc 2 places .150 .140 ( 3.81 3.56 ) dia. pinout table type pin 1 pin 2 pin 3 to - 257, -5v regulator ground v in v out disclaimer: 1- the information given herein, including the specifications and dimens ions, is subject to change wi thout prior notice to impr ove product characteristics. before ordering, purchas ers are advised to contact the sensitron semiconductor sales department for the latest version of the datasheet(s). 2- in cases where extremely high reliabilit y is required (such as use in nuclear power control, aerospace and aviation, traffic equipment, medical equipment , and safety equipment) , safety shoul d be ensured by using semiconduc tor devices that feature assured safety or by m eans of users? fail-safe precautions or other arrangement . 3- in no event shall sensitron semiconducto r be liable for any damages that may result from an accident or any other cause duri ng operation of the user?s units according to the datas heet(s). sensitron semiconductor assumes no responsibility for any intellectual property claims or any other problems that may result from applications of info rmation, products or circuits described in the datasheets. 4- in no event shall sensitron semiconduc tor be liable for any failure in a semic onductor device or any secondary damage result ing from use at a value exceeding the absolute maximum rating. 5- no license is granted by the datasheet(s) under any patents or other rights of any th ird party or sensitron semiconductor. 6- the datasheet(s) may not be reproduced or duplicated, in any fo rm, in whole or part, without the expressed written permissio n of sensitron semiconductor. 7- the products (technologies) de scribed in the datasheet(s) are not to be provi ded to any party whose purpose in their applica tion will hinder maintenance of international peace and safety nor are they to be applied to that purpose by their direct purchasers or any thir d party. when exporting these products (t echnologies), the necessary procedur es are to be taken in accordance with related laws and regulatio ns.
|
